Difference between revisions of "Philips HPI-T and HPI-T Plus"

Jump to navigation Jump to search

Philips HPI-T and HPI-T Plus (view source)

Revision as of 10:27, 2 October 2021

2,114 bytes removed ,  10:27, 2 October 2021
m
→‎Review
Line 82: Line 82:


== Review ==
== Review ==
These high pressure sodium vapour lamps are compact light sources that are viable for wide area lighting. Their poor colour reproduction and large output means that they are entirely suited to outdoor lighting or greenhouses as grow light. Compared with fluorescent lamps they were very compact, having great performance at low temperatures. A very long lifetime, that was around 16 to 25 times higher than tungsten lamps, and almost double that of some fluorescent lamps, meant that these lamps are well suited for use in places where lamp replacement was costly, as in high bay lighting, street lighting, tunnel lighting.  
These metal hallide lamps are better suited for outdoor lighting due to their high power rating and good colour reproduction. Long service lifetime is also another major feature of these HPI-T lamps. Large wattage fixtures were very popular especially for flood lighting with boxy, asymmetric or symmetric lighting patterns. The most popular power ratings were 250 and 400 Watts. The lamp itself fares well in terms of light output but the point light source nature of the lamp relegates it to accent or directional rather than general lighting.


High pressure sodium lamps had higher light output, almost double, of mercury vapour lamps while having very low quality colour reproduction. This means that mercury vapour lamps were still suited for areas where colour reproduction was moderately important and there was still an advantage from compact light sources. However, street lighting was a very important market as the lamp's efficiency ensured cost savings in labour and electricity use, after the 1970s oil crisis. There were some advances in colour reproduction with different lamp technology but standard lamps were not favourite of industrial, workshop lighting commercial premises. The light spectra was, however, highly beneficial for plant growth.
Exterior lighting is a good application as most gardens and outside areas are well showcased. The lamps themselves do release some heat meaning that closed fixtures are not well suited if not specifically built for this purpose. Care should be taken when using these metal-hallide lamps as they are sensitive to the operating position especially when inside enclosed fixtures. Compact, boxy symmetric and asymmetric fixtures were popular. Improper heating of lamp can destroy it prematurely and present a safety hazard so special precaution should be exercised. Even if lamp warm up time is low, achieving high output quite quickly, they are slow to restart, 10 minutes pauses not being uncommon.
 
The inherent flicker of mains voltage lamps is very low even with conventional gear due to the fact that a large amount of light happens due to thermal emission and balance of the temperature of internal arc tube. There were some electronic medium frequency gear similar with ones used on fluorescent lamps but they were very costly. However, sodium and metal hallide gears are generally compatible, meaning that most sodium lamps can be easily replaced with compatible wattage metal hallide lamps that have a much better colour appearance, sacrificing some energy efficiency due to different lamp technology. The requirement for ignitors along ballasts while it raises total cost and increases complexity, as well as raising the risk due to passing thousands of volts through some wires, means that fixtures have a clear advantage of maximum useful light and restart in case of power failure in almost one minute.
 
Fixtures are generally compact, considering the light output made available, but are generally heavy due to the bulky electromagnetic gear being used. There are directional and omni-directional fixtures that are suited to various purposes. In street lighting, the well known cobra-head style lamppost was used, and they may still be available for purchase. They were only moderately effective as light covered a large area but a considerable amount of light was lost due to the fixture directing some of it upwards, with no control. Omni-directional fixtures were used in residential areas and parks, where ambience was more important than efficiency. Indoor fixtures were centered on the typical high-bay or low-bay types due to their application in greenhouses where light has to be directed entirely downwards. Other fixtures were compact, having a boxy design, with a symmetrical or asymmetrical lamp placement that was suited for flood lighting. These type of lamps were used outdoor, for floodlighting. There were no home designed fixtures as these lamps were never used in home environments.


== Operation ==  
== Operation ==  
Retrieved from "https://adnoteh.ro/retrowikid/index.php/Special:MobileDiff/718"

Navigation menu